Installation Guide & Videos
Your new water-saving devices are only effective if they get installed! Don’t worry, we’ve got you covered with easy-to-follow installation videos for each of your water-saving devices.
Water-Saving Showerhead:
Installing your new showerhead is a quick and simple task. Start by unscrewing your old showerhead. You may need pliers to grip the threads, but don’t overdo it – apply just enough pressure to loosen it. Once the old showerhead is off, wrap a small piece of pipe tape around the threads of the pipe. Then, screw the new showerhead on by hand – finger-tight is perfect (you can use a wrench to gently tighten further if needed). Turn on the water and check for any leaks around the pipe threads. Note: If you can’t remove it easily, consider calling a professional plumber for help. Tip: Place a towel on the shower or tub floor for protection if a tool is accidently dropped.
5-Minute Shower Timer:
Installing and using your new shower timer is simple! Start by slightly wetting the suction cup and sticking it to the shower wall. When you get in, rotate the timer to start the sand flow. The timer runs for exactly 5 minutes – try to finish your shower before the sand runs out to save water with every use!
Bathroom Faucet Aerator:
Installing your new water-saving bathroom faucet aerator is fast and easy. Begin by removing the old aerator (if there is one). If it is stuck in place, use a rag and pliers for extra grip. Your new aerator comes with several rubber washers, use one or more to ensure a tight, leak-proof fit. Screw the new aerator onto the faucet – just finger-tight. Turn on the water and make sure that there are no leaks around the aerator.
Toilet Tank Bag:
Installing your new toilet tank bag is fast and easy! First, lift the lid off the toilet tank. Fill the tank bag with water in the sink, then slowly lower it into the tank, hooking it onto the side. You may need to flush the toilet while lowering the bag into place to prevent overflow. Once installed, the bag will displace some of the tank water, reducing the amount used per flush. Now, you’re saving water with every flush! Tip: To fit smaller tanks, you can partially fill the bag, but be careful—too little water can cause it to float. Make sure the bag doesn’t interfere with any internal components like the flush lever or flapper. Note: Newer high-efficiency toilets use less water per flush and may not benefit from using a toilet tank bag.
Plumber’s Tape:
Plumber’s tape is a handy tool for sealing and lubricating pipe threads. It’s easy to use and safe for many applications. To apply, wrap the tape around the pipe threads in a clockwise direction, matching the direction the fitting will turn on the pipe. The tape should lie flat and snugly over the threads. Wrap it around the pipe 3-4 times, keeping tension as you wrap. Once wrapped, pull the tape sharply to break or cut it off, then smooth the loose end down over the threads. Your pipe is now ready for the new fixture!
Toilet Tank Dye Detection Strips:
Using toilet tank dye detection strips is easy! Remove the toilet tank lid and drop one dye strip into the back of the tank. Do NOT flush the toilet. Wait 20 minutes and check to see if any colored water is present in the toilet bowl area. If colored water is present, then the flapper is leaking water from the tank into the bowl and should be replaced. Tip: Take the old flapper with you to the store to ensure you get the correct size and type of flapper for your specific toilet model.
Drip Gauge:
Using your new drip gauge is easy! Place the vial under a leak for 5 seconds and then read the “Drip Vial” markings at the water level. The gallons per day (GPD) and gallons per year (GPY) markings will show just how much water is being wasted. For drip emitter systems, simply divide the GPD number by 24 to determine the gallons per hour flow rate. To use as a rain gauge, place the vial in an open area, free from obstructions like trees. Secure the vial to prevent it from being blown over by wind. It can be partially buried or pinned against something sturdy. After a rain event, read the rain gauge markings at the water level.
Automatic Hose Timer:
Installing your new hose timer is fast and easy! Turn off your outdoor hose spigot and remove the garden hose. Screw the threaded brass intake of the timer to the spigot and attach your garden hose or irrigation system. Set the timer by turning the raised dial clockwise to the desired time interval. Turn on the spigot to your preferred flow rate, set the timer, and check all connections for leaks before leaving your system unsupervised. Now your timer will shut off the flow of water at the end of the selected interval.
Drip Irrigation Repair Unit:
Using your new drip irrigation repair kit is easy! The small end of the goof plug is used to plug 1/4” tubing, or a 1/4” hole in mainline tubing. The large side is used to plug worn out holes in 1/2” polytubing. If this does not plug a worn out hole, you will need to replace that section of tubing. The connector is used to join two ends of 1/2” or 5/8” tubing. Unscrew the fitting nuts from the housing and insert one end of tubing into a fitting nut. Push the tubing over the barbed side of the fitting. Thread the fitting nut firmly onto the housing and repeat these steps for the other end of tubing.